Menu
![Ga-p35-ds3l Drivers For Mac Ga-p35-ds3l Drivers For Mac](/uploads/1/2/6/1/126154402/537975926.jpg)
Gigabyte Ga P35 Ds3l Drivers
Similar Content
- By ludufreInstalling macOS Mojave 10.14.6 on Gigabyte Z370N WIFI + i7 8700K + UHD 630
Changelog:
09/01/2019 15:57h GMT-0
- Updated to 10.14.6.
06/10/2019 00:44h GMT-0
- Completely rewritten.
10/17/2018 08:12h GMT-0
- Fix Kexts permissions commands adjusted.
- Removed FrameBuffer patch that is not needed.
- Added audio solution and HDMI.
- Unfortunately DisplayPort does not work.
- Replaced Wifi/BT with DW1560 (BCM94352Z)
10/11/2018 04:15h GMT-0
- Added USB 3.0 patch.
- Adjusted some steps.
- Changed text formatting.
10/11/2018 03:42h GMT-0
- Added missing UEFI configuration.
10/07/2018 00:36h GMT-0
- First version.
What works and what does not
- Processor: Intel Core i7-8700K -> Work. All SpeedStep stages.
- Video Card: Intel UHD 630 -> Work. QE/CI and Metal.
- Chipset: Intel Z370 -> Work.
- HDMI 2.0 (1st) -> Work.
- HDMI (2nd) -> Work.
- DP -> Not tested yet.
- Audio: ALC1220 -> Work.
- HDMI Audio -> Work.
- WiFi/Bluetooth -> Not work. Replaced with BCM94360CS2.
- Ethernet (1st) -> Work.
- Ethernet (2nd) -> Work.
- USB3.0 -> Work.
- Sleep -> Work.
- Airdrop, Handoff, Instant Hotspot and Continuity -> Work after replaced wireless.
Todo
- Make audio work.
- Make HDMI audio work.
- Test DisplayPort.
- Make second ethernet work.
- Replace Wifi/Bluetooth.
- Test DP.
What you need to install
- Running install of macOS
- One USB flash drive of 8GB or bigger
- macOS Mojave install app
- Clover Configurator
- Clover EFI
- Clover Configurator
- Some KEXTs and SSDT patches
How create create the install flash drive
Prepare install flash drive
Format the flash drive with GUID partition mapping and name it 'Install'.
- Open Disk Utility.
- Click in View, then 'Show All Devices'.
- Select the destination flash drive, then Erase.
- Name: Install, Format: Mac OS Extended (Journaled) and Scheme: GUID Partition Map
Create install flash drive
Open terminal and run this command:
sudo /Applications/Install macOS Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/Install --nointeraction This will take about 30 minute s. / 8 minutes with USB 3.0
Install bootloader
Download the CloverEFI (used 5058, from Automated Clover Builds) and install with this options on 'Install macOS Mojave':
- Install for UEFI booting only
- Install Clover in the ESP
- UEFI Drivers - Recommended drivers (check all)
- UEFI Drivers - Human Interface Devices (check all)
- UEFI Drivers - FileVault 2 UEFI Drivers (check all, If you are going to use FileVault)
- UEFI Drivers - Additional drivers - NvmExpressDxe (if you are going to use NVMe)
Make things works
We'll make a full working flash drive, so follow these instructions:
Will be mounted the EFI partition of the flash drive.
Open the the /Volumes/EFI/CLOVER/config.plist inside this new partition with Clover Configurator (used 5.5.0.0)
Important modifications
config.plist
ACPI Page
- Check: SSDT - PluginType
BOOT Page
- Add: Arguments - darkwake=2
- Check: Legacy - XMPDetection=Yes
KERNEL AND KEXT PATCHES Page
- Check: KernelPm
RT VARIABLES Page
- Change: CsrActiveConfig - 0x3E7
SMBIOS Page
- Change: Macmini8,1 - Mac mini (Late 2018) | Intel Core i7-8700B @ 3.20 GHz
- Click: Generate New (few times in the two buttons)
Need some Kexts in the folder /EFI/CLOVER/kexts/Other/
- Download the HWSensors 3 from here. I used the FakeSMC.kext, ACPIMonitor.kext, ITEIT87x.kext and IntelCPUMonitor.kext inside of DMG version r240.
- Download the Lilu.kext from here. I used the version 1.3.8.
Intel UHD 630
ACPI Page
- Uncheck: Fixes - AddHDMI
- Uncheck: Fixes - FixDisplay
- Uncheck: Fixes - FixHDA
GUI Page
- Change: Screen Resolution - 3840x2160 (My monitor is 4K)
Need a Kext in the folder /EFI/CLOVER/kexts/Other/
- Download the WhateverGreen.kext from here. I used the version 1.3.1.
Audio ALC 1220 and HDMI audio
BOOT Page
- Add: Arguments - alcid=11
DEVICES Page
- Change: Audio - Inject - 11
- Uncheck: Audio - AFGLowPowerState
- Uncheck: Audio - ResetHDA
Need a Kext in the folder /EFI/CLOVER/kexts/Other/
- Download the AppleALC.kext from here. I used the version 1.4.0.
All USBs (2.0, 3.0, Type-C, internal)
KERNEL AND KEXT PATCHES Page - KextsToPatch
- Name*: com.apple.iokit.IOUSBHostFamily
- Find* [HEX]: 83FB0F0F
- Replace* [HEX]: 83FB3F0F
- Comment: USB Port Limit Patch 1 PMHeart/DalianSky
- MatchOS: 10.14.x
- Name*: com.apple.iokit.IOUSBHostFamily
- Find* [HEX]: 83FB0F0F
- Replace* [HEX]: 83FB3F0F
- Comment: USB Port Limit Patch 2 PMHeart/DalianSky
- MatchOS: 10.14.x
- Name*: com.apple.driver.usb.AppleUSBXHCI
- Find* [HEX]: 83FB0F0F
- Replace* [HEX]: 83FB3F0F
- Comment: USB Port Limit Patch 3 PMHeart/DalianSky
- MatchOS: 10.14.x
- Name*: com.apple.driver.usb.AppleUSBXHCI
- Find* [HEX]: 83FF0F0F
- Replace* [HEX]: 83FF3F0F
- Comment: USB Port Limit Patch 4 PMHeart/DalianSky
- MatchOS: 10.14.x
Need a Kext in the folder /EFI/CLOVER/kexts/Other/
- Download the USBInjectAll.kext from here. I used the version 2018-1108.
Need SSDT patch in the folder /EFI/CLOVER/ACPI/patched/
- Download the SSDT-EC.aml, SSDT-UIAC.aml and SSDT-USBX attached bellow.
Wifi and Bluetooth (BCM94360CS)
Works out of box (plug 'n' play).
LAN Cards
Need a Kext for feach card in the folder /EFI/CLOVER/kexts/Other/
- Download the IntelMausiEthrenet.kext from here. I used the version 2018-1031.
- Download the SmallTreeIntel82576.kext attached bellow. I do not remember where I found it.
Now you can start the instalation without problem (I guess).
How install
UEFI Setup Configuration and Installation
UEFI configuration
- Shutdown and insert the flash.
- Power on with DEL pressed to enter BIOS setup.
- Change value: Periphelrals - Initial Display to IGP
- Change value: Periphelrals - USB Configuration - XHCI Hand-off to ENABLE
- Change value: Chipset - VT-d to DISABLE
- Change value: Chipset - Internal Graphics to ENABLE
- Change value: Chipset - DVMT Pre-Allocated to 128M
- Save & Exit Setup
- Now, hold the F12
- In the list, select your flash drive.
- It will show twice. One with UEFI prefix and another without.
- Select with UEFI prefix. Ie.: 'UEFI: Sandisk Cruzer'
The installer will start.
Format destination disk
Format the disk with GUID partition mapping and name it 'HD'.
- Select Disk Utility in the list, then press Continue.
- Click in View, then 'Show All Devices'.
- Select the destination Disk, then Erase.
- Name: HD, Format: APFS and Scheme: GUID Partition Map
Close Disk Utility.
Select 'Install macOS', then Continue.
Follow instructions in screen.
After install
After first part install the system will reboot.
The second part of the installation will begin. This will take 16 minutes.
Post installation
Install bootloader
When the second part of install finish, the system will reboot again.
After performing the user initial setup and go to the desktop, you need to install Clover on internal disk.
Open the Clover installer inside flash drive that you copied before.
Use same options above but choose the system partition this time.
Now you need to replace the EFI folder inside your destination disk EFI parittion, with EFI folder inside flash card EFI partition.
If the flash drive EFI partition of your destination disk or flash drive is unmounted:
Mount with terminal 'sudo diskutil mount /dev/rdiskXs1'. To know what X is, use 'diskutil list', most likely is 0 for destination disk and 1 for flash drive.
Then, eject the flash drive.
Last step
Move all Kexts from EFI partition to /Library/Extensions, with those commands in Terminal:
sudo cp -R /Volumes/EFI/EFI/CLOVER/kexts/10.14/* /Library/Extensions/sudo chmod -R 755 /Library/Extensionssudo chown -R root:wheel /Library/Extensionssudo kextcache -i / Restart the system.
It's done!
Updates
System update 10.14.6
- Download and open latest CloverConfigurator
- Open Mount EFI and click in Mount Partition in EFI Partitions list
- Click in Open Partition that appears
- Go to EFI -> CLOVER
- Backup config.plist and ACPI folder to desktop
- Go back and delete CLOVER folder
(If you restart now you can't boot in macOS - DON'T RESTART)
- Download latest Clover and install (link and config above)
- Replace config.plist and ACPI folder from your desktop
- Update Lilu.kext, AppleALC.kext, WhateverGreen.kext, HWSensors kexts (FakeSMC, ACPIMonitor, IntelCPUMonitor, ITEIT87x) in /Library/Extensions/
- Run:
sudo chmod -R 755 /Library/Extensionssudo chown -R root:wheel /Library/Extensionssudo kextcache -i /
- Install macOS Update 10.14.6 and restart
And last but not least
I would like to thank the following community members, by making these dream possible:
@crushers, @snatch, @apianti, @blackosx, @blusseau, @dmazar, @slice2009, @autumnrain, @phpdev32, @EMlyDinEsH, @RehabMan, @Scellow, @mitch_de, @Shailua, @Andy Vandijck, @maxfierke, @ArturXXX, @LexHimself, @brumas and all others members involved directly or indirectly.
Z370N-WIFI v2.zip - By Pedro DinizHello Friends, how are ya?
Could you help me with a problem?
I followed some guides like: https://www.insanelymac.com/forum/topic .. coffeelake -dsdt /
and the installation of high Sierra 10.13.6 (17G8030) and nvidia webdrivers (correspondent to OS version) went smoothly, the problem starts when I try to boot the GPU.
Hardware:
MOBO: Aorus B360M gaming 3 (rev.1)
CPU: i5 8400
GPU: GTX 1060 OC Galax redblack
BIOS:
Fast boot - disabled
windows 8/10 features - other os
lan pxe - disabled
storage boot option - UEFI
other pci devices - UEFI
Initial display output - PCie 1 slot
Intel's Platform Trust Technology (PTT) - disabled
sata mode selection - AHCI
XHCI hand off - enabled
VT-d - disabled
internal graphics - auto
The problem is:
I can log into the system normally without using my nvidia GPU but when I boot the system with the flags for webdrivers to work I fall into the login screen but it keeps flashing, I can see the mouse and I can move it but the screen flashes and the following error appears when the screen goes 'black': IOConsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0. I searched for this error on the internet and tried to solve but to no avail so far.
If someone can help me I would be extremely grateful! thanks in advance!
Clover file attached.
CLOVER.zip - By tragediana150Hi everyone!
Long time no see guys!
As you can see I am not new user of Insanely and do not want to post in incorrect section, but I can not find any similiar topic at all. I,ve searched the forum and the web and I can't find a solution.
My question is that is there any possibility to install Mavericks 10.9.5 on external drive on the newest Macbook Pro 13 from 2018? I know that the Intel Coffee Lake is new generation of CPU's and there is no drivers in Mavericks system to run this CPU, but I was thinking about it alot and I decided to write here. Because if we can install all the newest OSX, macOS on older machines then maybe we can install older systems on newer builds?
P.S. If I wrote in incorrect topic then please move this thread to the right section, I will be grateful - By ignnHello!
I want install Hackintosh on my hardware
Motherboard: Gigabyte B360M-HD3
CPU: I3-8100
GPU: Intel HD630
Anyone has had experience installing on this hardware? Is there a guide? Thanks in advance - By Amit MeenaThis card is working OOB, but it has some graphical issues as per attachments.
If someone has a solution please share.
Gigabyte P35 Ds3l Bios
Update CPU ID Specificatios: Intel P35 ICH9 Chipset 1. Supports Intel Core 2 multi-core and upcoming 45nm processors 2. Trucking companies that hire student graduates. Supports DDR2 1066* memory for outstanding system performance 3. I am a noob to RAID of any sort and I've been told that my board does NOT have RAID ports at the same time some other folks told me i can do RAID0 with on board ports.